Plumbing for Beginners: The Essentials for Installing a Bathtub
Plumbing for Beginners: The Essentials for Installing a Bathtub
Blog Article
The article below pertaining to How to Install a Bathtub Yourself is relatively enlightening. Don't skip it.
Installing a bath tub isn't exactly rocket science, but it does require strong plumbing, carpentry, and occasionally, tiling skills. Replacing an old tub with a brand-new one is likewise a moderately challenging job. If the old tub is conveniently obtainable, the project can move quickly; if you have to open a wall surface to eliminate the old tub and place the new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's abilities, although you will require an assistant to leave the old bathtub and also embeded in the brand-new one. Make certain you have certified yourself for the task as well as are comfortable attempting it. Rather than working with a service provider to take control of a halfway-completed job, it is much better to think about using one prior to you begin. Chances are you might require a professional plumber to make tube links.
This short article will aid you mount a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub and don't need to change the setup of your previous water pipes.
Your devices as well as product list should consist of the following:
Planning for the Setup
First of all, the supporting framework supplied with the bath must be fitted (if required) according to the maker's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to see to it that if the faucet features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets device to stop stress on the tub.
Fit the versatile faucet ports to the bottom of the two taps making use of 2 nuts as well as olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet via the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you utilize all of the provided washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to currently be ready to be fitted in its final placement.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installment, after that the first thing you ought to do is disconnect the water system. After doing so, turn on the faucets to drain any water continuing to be in the system. The procedure of getting rid of the existing taps can be fairly bothersome due to the restricted gain access to that is often the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a towel ready for the continuing to be water that will come from the pipes. As soon as the supply pipes have been eliminated, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from turning during this procedure. Once the taps have been eliminated, the holes in the bath/basin will have to be cleansed of any old securing substance.
Prior to carrying on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Tub
Using both wood boards under its feet, put the bath tub in the required setting. The wood boards are practical in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small factors.
The following goal is to ensure that the tub is leveled all round. This can be attained by checking the level as well as adjusting the feet on the bathtub until the spirit level reviews degree.
To mount taps, fit all-time low of the outermost versatile faucet connector to the suitable supply pipeline by making a compression sign up with; then do the very same for the various other faucet.
Switch on the water system and examine all joints as well as brand-new pipework for leakages and also tighten them if needed. Load the tub and likewise examine the overflow outlet as well as the normal electrical outlet for leakages.
Lastly, take care of the bathroom paneling as explained in the producer's user's manual. Tiling and also sealing around the bathtub ought to wait until the bathtub has been made use of a minimum of once as this will certainly settle it right into its last placement.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic port to prevent damage to the string. One end of the port fits on the plastic tail of the tap as well as the various other end provides a link to the existent supply pipes.
If you require to fit a monobloc, then you will certainly call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, place the tap in the placing hole in the bath/basin ensuring that the washing machines are in place in between the faucet and also the sink. Protect the faucet in place with the producer provided backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular tap adapters. The former kind should be linked to the tap ends initially, tightening up just by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the installation can move enough to fracture a rigid seal, triggering the water to permeate the wall surface in between the bathroom as well as the tiling, bring about issues with moisture as well as possible leaks to the ceiling below.
You can select from a variety of coloured sealants to blend in your fixtures and installations. They are marketed in tubes and cartridges, and also are capable of sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of drenched paper or soft rope. Bear in mind to always fill the tub with water before securing, to permit the activity experienced when the tub is in usage. The sealant can fracture rather early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also easily available on the market. It is suggested to fit the floor tiles utilizing water-resistant or waterproof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy more info about Tools You Need to Install a New Bathtub ? Write a comment below. We would be delighted to hear your views about this write-up. We are looking forward that you visit us again soon. Sharing is caring. Helping others is fun. Thank-you for going through it.
Immediate relief, just a call. Report this page